Polished the barrel on my CW9 (Photo)

[Kahr9mmGuy]

Just finished polishing entire barrel including feed ramp and chamber throat. 1 good pass with dremel, cloth bit and Mother Billet metal polish. Finished with massive hand polishing with rags and Mother Billet metal polish.

http://i852.photobucket.com/albums/ab89/Glock40guy/024_zps961a3a87.jpg (http://s852.photobucket.com/user/Glock40guy/media/024_zps961a3a87.jpg.html)

[Pukindog12]

Shiny!!! Looks good!

[gb6491]

Nice work on that (pretty good photo as well):)
Regards,
Greg

[Acasper708]

Nice!
I just recently did my CW45 barrel. Also a few of the parts.
http://img.tapatalk.com/d/13/06/27/yve3yjuz.jpg

I also polished the inside of the slide where it was rubbing on the barrel, the guide rod, firing pin, and firing pin passage.

I used a Qtip and put jewelers rouge on it. Then stuck the Qtip in a drill and it shined up the passage pretty good.

[yqtszhj]

man that is super shiny

[Kahr9mmGuy]

Before I polished my barrel I had a hard time getting a round to chamber without using slide release lever but now since I polished the feed ramp to the point you can shave in her along with the whole barrel and chamber throat I can chamber a round by racking the slide with ease :D

[Buckshotshorty]

Looks so good you gave me incentive to do my CM9 barrel. It came out looking as good as the chrome on the bumper of a brand new '58 Buick!

[Kahr9mmGuy]

Looks so good you gave me incentive to do my CM9 barrel. It came out looking as good as the chrome on the bumper of a brand new '58 Buick!
After your all done wipe her down really good with a lead removal cloth from Birchwood Casey and she shines up more at the end:D

[dkmatthews]

Very inspirational, Kahr9mmGuy!

[jocko]

IMO kahr does a greatjob inpolishing their feed ramps. that bein said, anonwer can even do better as kahr9mmguy stated. sometimes the proof is indeedin the puddin. Just sayin

[Ikeo74]

Now you polished barrel guys won't want to shoot those guns because it will ruin your polish job.:rain:

[jocko]

been shootin my pMJ9 polished barrel and feed ramp for 5 years. Trust me, it eems to clean easier even.I use the Hoppe's snakealot while at the range and it sure brings b ack theshine PRONTO. Just sayin.

[nuke]

That looks superb!

[RevRay]

Just finished polishing entire barrel including feed ramp and chamber throat. 1 good pass with dremel, cloth bit and Mother Billet metal polish. Finished with massive hand polishing with rags and Mother Billet metal polish.

I have a Dremel that I took home when my dad died ... but it did not come with any cloth bits ... only cutters and various abrasive bits. Could someone be more specific regarding what I should be looking for in order to polish a barrel. Would one of the kinds in the links below be ok to use.

http://www.ebay.com/itm/12-7-8-BUFFING-POLISHING-WHEEL-FELT-FOR-DREMEL-/280561271625?pt=LH_DefaultDomain_0&hash=item4152c14349

http://www.ebay.com/itm/20-FELT-POLISHING-BUFFING-WHEELS-W-MANDRELS-FOR-DREMEL-/300933656157?pt=Power_Tools&hash=item46110b2e5d

http://www.ebay.com/itm/12-White-Yarn-Polishing-Cloth-Buffing-Wheels-Used-w-Dremel-And-Rotary-Tools-/400389571771?pt=LH_DefaultDomain_0&hash=item5d391404bb

[MW surveyor]

RevRay -

You can do the same thing using finer and finer grades of wet/dry paper. I polished just the chamber area on my CW9 starting with 600 grit and light oil for lube, then 1000 grit with light oil and 1500 grit with light oil. After that finished/polished using Mother's Mag polish and old T shirt material.

[Buckshotshorty]

I have a Dremel that I took home when my dad died ... but it did not come with any cloth bits ... only cutters and various abrasive bits. Could someone be more specific regarding what I should be looking for in order to polish a barrel. Would one of the kinds in the links below be ok to use.

http://www.ebay.com/itm/12-7-8-BUFFING-POLISHING-WHEEL-FELT-FOR-DREMEL-/280561271625?pt=LH_DefaultDomain_0&hash=item4152c14349

http://www.ebay.com/itm/20-FELT-POLISHING-BUFFING-WHEELS-W-MANDRELS-FOR-DREMEL-/300933656157?pt=Power_Tools&hash=item46110b2e5d

http://www.ebay.com/itm/12-White-Yarn-Polishing-Cloth-Buffing-Wheels-Used-w-Dremel-And-Rotary-Tools-/400389571771?pt=LH_DefaultDomain_0&hash=item5d391404bb


Either the first or second worked for me.