Hey Ed M, look what I did...

[yqtszhj]

Well, I did it today.


I traded this
https://s26.postimg.cc/vfdf2du15/93_DFEC11-_B2_F7-47_A0-86_E4-53_B3631_DE632.jpg

For this

https://s26.postimg.cc/g43m1prjd/IMG_20180507_141336282.jpg

Needs a little TLC and some CGW parts and it will be good to go.

[berettabone]

A fine trade.............from the dark side, back to reality. I'm proud of you.:p Wouldn't mind one of those myself.

[kenemoore]

Nice, I would have done that too.

[kenemoore]

Nice, I would have done that too.

[Bawanna]

OK for us CZ challenged folks, is that the Rami? Can't make the picture big enough to tell for sure.

I would have done that too, whatever it is.

[O'Dell]

I always recommend a move from Glock to anything else! :rolleyes:

[yqtszhj]

Yeah, that’s the Rami decocker. Got it for an even trade. I got a deal on that G26 last fall so I’m into the Rami for cheap (relatively speaking.) A higher resolution pic below. It cleaned up real nice too. Looks like it wasn’t shot much.

https://s26.postimg.cc/g5i591isp/DE86_F619-5_F88-4203-8816-937_B0_FF76164.jpg

[jeepster09]

Very nice!!!!

[Ed M]

Well, I did it today.


I traded this
https://s26.postimg.cc/vfdf2du15/93_DFEC11-_B2_F7-47_A0-86_E4-53_B3631_DE632.jpg

For this

https://s26.postimg.cc/g43m1prjd/IMG_20180507_141336282.jpg

Needs a little TLC and some CGW parts and it will be good to go.

Congratulations!!!

Woohoo! You're gonna love this one. REALLY good shooter.

Mine had issues with the 14 round mag. Failure to feed - rounds just jammed against the bottom of the feed ramp.

Had to replace the mag springs with Wolff +5% springs for a full size CZ 75, and that took care of it.

You'll probably want the pinkie extension for the 10 rd mag too.

https://www.ebay.com/itm/CZ-2075-Rami-Grip-Extension-Fits-both-9mm-and-40-S-W/253594350659?epid=4006251435&hash=item3b0b66b443:g:M9sAAOSwqrtWpYzX

[yqtszhj]

Congratulations!!!

Woohoo! You're gonna love this one. REALLY good shooter.

Mine had issues with the 14 round mag. Failure to feed - rounds just jammed against the bottom of the feed ramp.

Had to replace the mag springs with Wolff +5% springs for a full size CZ 75, and that took care of it.

You'll probably want the pinkie extension for the 10 rd mag too.

https://www.ebay.com/itm/CZ-2075-Rami-Grip-Extension-Fits-both-9mm-and-40-S-W/253594350659?epid=4006251435&hash=item3b0b66b443:g:M9sAAOSwqrtWpYzX

Range repeort:
200 rounds and the only issues were with the 14 round magazine. As you said the 14 round springs are weak. I had the same issues you did so a spring is in order and you could tell it was weak when loading the mag. The 10 round mag ran flawless.

I think the guy traded because it had a few little issues that needed addressing that maybe he couldn’t fix. First was the 14round mag I guess. Then the front site wasn’t centered so it shot to the left. It was like that from the factory because you could see the stake marks on the sight and slide so the rear sight was all the way to one side to compensate. I drifted it to the center so it outta be good now. The trigger pin wasn’t flaired well so it would drift a bit. Fixed that now it’s a non issue. And the grip bushings needed another half turn so the grips would sit flush. You could see where he fudged the head of one of the grip screws trying to get it flush to no avail. I actually like the factory rubber grips. They’re real easy to keep a hold on to.

I got awarded a Visa gift card so I’m thinking that the perfect use for it would be a few Cajun gun works parts, in particular the 85C combat trigger, floating trigger pin, and maybe the Rami lighter spring kit. Those items and a polish job on the internals while it’s apart and it should feel like a custom pistol.

That was one of the best trades I’ve made in a long time.

[b4uqzme]

I’m gonna hafta get me a couple glocks for trade bait. :rolleyes: Well done.

[Ed M]

I bought an extra 10 rd mag and another 14 rd mag. The spring on the original 14 rd mag was just limp. It was the big offender for the FTF issues. While I was at it, I replaced the 10 rd mag springs with the Wolff +5% CZ 75 compact springs, and the 14 rd springs with the +5% full size CZ 75 springs. Also polished the feed ramp, as it looked crappy.

It's been 100% since, with about 500 rounds through it. The trigger smoothed out so nicely that I'm not even tempted to mess with anything. Accuracy is incredible for a short barrel.

If you need a nice leather OWB holster, Winthrop makes a real beauty for a reasonable price. Fit is perfect, as it's made for the RAMI.

In all but hot weather, or challenging clothing, this is my carry weapon of choice. It carries very well, and with a spare 14 rd mag on my weak side hip, it's got plenty of firepower.

[kenemoore]

Range repeort:


Then the front site wasn’t centered so it shot to the left. It was like that from the factory because you could see the stake marks on the sight and slide so the rear sight was all the way to one side to compensate. I drifted it to the center so it outta be good now.


The front sight on the RAMI doesn't slide in from the front like the other CZ's? That's one of the things I like about them.

[yqtszhj]

The front sight on the RAMI doesn't slide in from the front like the other CZ's? That's one of the things I like about them.

Yeah the Rami slides left or right instead of in from the front like the other CZ’s with the cross pin that holds it in which is why it was off center. It was easy to tap just a bit to center it up but if it went in from the front it would have been a non issue.

[ltxi]

Yeah the Rami slides left or right instead of in from the front like the other CZ’s with the cross pin that holds it in which is why it was off center. It was easy to tap just a bit to center it up but if it went in from the front it would have been a non issue.

Or a big issue. I'm one who prefers windage adjustable front sights.