fastkahrs
02-01-2020, 01:41 PM
I got a good buy on a lightly used CW9 a few years ago. It didn't appear to have been shot much. I sent the slide off for some milling work and was very disappointed with the outcome.
Recently, wanting to make use of this pistol, I ordered a new slide for it. After reading several reports of PM9 slides on CM9 frames and P9 slides on CW9 frames, I figured I would give that a go. P9 slide w/ all CW9 internals, barrel and frame. After shooting 54 flawless rounds. I noticed peening on both sides of the barrel, located on the raised ring/lug just forward of the chamber. I have since fired about 210 rounds, and had (3) failure to feed's. The round was partially in the chamber, a slight push on the rear of the slide chambered the round. The most recent 54 rounds fired flawlessly.
The flat spots may have grown a slight bit since I first noticed but not much. See any issue here??
Thanks
https://scontent.fewr1-6.fna.fbcdn.net/v/t1.0-9/p720x720/83773581_10214960729964063_8015471085388562432_o.j pg?_nc_cat=106&_nc_oc=AQn9Dl8Kil5hcMBN8Eimpft5bHduBkg-1NhS_Y3MbRAFUDV1okJhM8krBAbPZRJjT-Pt6bEkTh-5nsCwVFF05v21&_nc_ht=scontent.fewr1-6.fna&_nc_tp=6&oh=ac26f6c70082d35c66706032bc9ffe05&oe=5EC5DCD4
https://scontent.fewr1-6.fna.fbcdn.net/v/t1.0-9/p720x720/84016784_10214960730844085_8729711553869250560_o.j pg?_nc_cat=106&_nc_oc=AQkYrNPJS5t6MY7p_pIrxh0mnlbqUk_CdD7YF7QA7zL buGN0pSJHx2WogtZPD70k-OD6hJoyH_DZxuHCwst4Y-qW&_nc_ht=scontent.fewr1-6.fna&_nc_tp=6&oh=1fe274c9fb2a94a20094ca1b060ba9ff&oe=5ECE2CD4
Recently, wanting to make use of this pistol, I ordered a new slide for it. After reading several reports of PM9 slides on CM9 frames and P9 slides on CW9 frames, I figured I would give that a go. P9 slide w/ all CW9 internals, barrel and frame. After shooting 54 flawless rounds. I noticed peening on both sides of the barrel, located on the raised ring/lug just forward of the chamber. I have since fired about 210 rounds, and had (3) failure to feed's. The round was partially in the chamber, a slight push on the rear of the slide chambered the round. The most recent 54 rounds fired flawlessly.
The flat spots may have grown a slight bit since I first noticed but not much. See any issue here??
Thanks
https://scontent.fewr1-6.fna.fbcdn.net/v/t1.0-9/p720x720/83773581_10214960729964063_8015471085388562432_o.j pg?_nc_cat=106&_nc_oc=AQn9Dl8Kil5hcMBN8Eimpft5bHduBkg-1NhS_Y3MbRAFUDV1okJhM8krBAbPZRJjT-Pt6bEkTh-5nsCwVFF05v21&_nc_ht=scontent.fewr1-6.fna&_nc_tp=6&oh=ac26f6c70082d35c66706032bc9ffe05&oe=5EC5DCD4
https://scontent.fewr1-6.fna.fbcdn.net/v/t1.0-9/p720x720/84016784_10214960730844085_8729711553869250560_o.j pg?_nc_cat=106&_nc_oc=AQkYrNPJS5t6MY7p_pIrxh0mnlbqUk_CdD7YF7QA7zL buGN0pSJHx2WogtZPD70k-OD6hJoyH_DZxuHCwst4Y-qW&_nc_ht=scontent.fewr1-6.fna&_nc_tp=6&oh=1fe274c9fb2a94a20094ca1b060ba9ff&oe=5ECE2CD4